Back to Blog
How-to Guides 2026-11-16 CD PROJEKT RED US Gear Store – CD PROJEKT RED Gear 0 views

David's Apartment Shadowbox: Display and Lighting Setup Guide

David's Apartment Shadowbox: Display and Lighting Setup Guide

Set up the Cyberpunk: Edgerunners David's Apartment Shadowbox with the right wall spot, power source, and light sensor mode. A practical display guide for a 12 x 8.5 in lit diorama.

The shadowbox is a lit scene, not just a framed print

The Cyberpunk: Edgerunners David's Apartment Shadowbox is a 12 x 8.5 in (30.48 x 21.59 cm) layered acrylic scene inside a black painted wood frame. It uses printed acrylic panels and a black-out plate to create depth, and the built-in LED lighting changes the mood of the room as light hits the floor and ceiling.

That means your display plan has two parts: where the box hangs, and how it gets power and light control. Get those right and the scene reads clearly in both daylight and a dark room.

What you are working with

Choose a wall spot before you mount anything

The shadowbox is designed to be seen, so treat the wall spot as part of the display, not an afterthought.

  1. Pick a wall with some contrast: The black painted wood frame and dark scene read best against a lighter or mid-tone wall. A very dark wall can swallow the frame edges.
  2. Leave room for the light to land: The lighting effect is most visible when the box is not crowded by shelves or furniture directly above and below it. Give the floor and ceiling light some space.
  3. Plan for power or batteries: You can insert batteries into the back compartment or use the included USB cable. If you want to use USB, choose a spot within reach of a power source or route the cable before mounting.
  4. Check the viewing height: Hang it at a height where the layered scene sits near eye level. The shadowbox is a small piece, so a lower, closer viewing position usually shows more detail than a high wall.

Mounting: what the supplied information confirms

The supplied product information confirms the size and materials but does not include a mounting method, hardware list, or weight rating. Before you drill or stick anything to the wall, check the back of the frame and any included hardware, and use a fixing appropriate for your wall type and the weight of the piece.

If you are not confident about wall fixings, a small shelf or a stable cabinet top is a simpler alternative. The shadowbox is 12 x 8.5 in, so it fits on many shelves, but leave clearance above it if you want the light to spill onto the ceiling.

Set the light sensor and power mode

The shadowbox has an On / Off / light sensor switch on the side. The light sensor itself is at the top of the shadowbox. Follow these steps to get the behavior you want.

  1. For automatic lighting, turn the light sensor switch to ON (I): This activates the sensor at the top of the shadowbox. The LED lights will turn on automatically when the room is dark and turn off when the room is bright.
  2. For manual control, turn the light sensor switch to OFF (0): Then use the Power button on the side of the shadowbox to turn the LED on and off as you like.
  3. Expect a real-time mood change: With the sensor on, the shadowbox lights up automatically in dark surroundings, changing the mood of the scene in real time. In a dark room, the black-out plate creates sharper shadows.

USB cable vs batteries: which power setup fits your room

Both options are supported by the supplied product information. The choice comes down to where the shadowbox lives and how often you want to think about power.

  • USB cable: Use the included USB cable when the shadowbox is near a power source. This avoids battery changes and suits a permanent wall or shelf spot.
  • Batteries: Insert batteries into the back compartment when a cable would be awkward or visible. You will need to replace them, so keep the back compartment accessible.

Make the lit effect work in your room

The shadowbox is at its most dramatic in a dark room, where the black-out plate creates sharp shadows and the light hits the floor and ceiling of the scene. In a bright room, the automatic sensor will keep the LEDs off, so the piece reads as a layered acrylic diorama rather than a lamp.

If you want the automatic effect, place the shadowbox where the top sensor can read the room light without being blocked. Avoid tucking it directly under a shelf that shades the sensor, and keep the top edge clear.

For a manual setup, the Power button lets you switch the LEDs on whenever you want the scene lit, even in daylight. That is useful if the shadowbox is part of a display shelf that you light for viewing.

A quick pre-display checklist

  • Confirm the wall spot: Check the 12 x 8.5 in footprint against your wall or shelf space, and make sure the top of the shadowbox is not blocked.
  • Decide on power: Choose USB or batteries, and make sure the back compartment or cable route is accessible.
  • Set the switch: Turn the light sensor switch to ON (I) for automatic lighting or OFF (0) for manual control with the Power button.
  • Test in the dark: With the sensor on, darken the room to confirm the LEDs activate and the shadows read as expected.
  • Expect slight color variation: Colors may vary from images shown due to monitor display variance.

Related Articles

Customer Service
Home
Products
Cart
Profile